ALTA PRO
BRIOT ALTA PRO
New productivity gains
Our technical development choices have led us to implement a new motorization and a 50% optimization of the grinding algorithms. The ALTA PRO thus sets new standards in terms of grinding time (43% less on average) and consequently a significant increase in your productivity gains.
New TBS (Tilted Bevel System)
ALTA PRO incorporates a new grinding wheel dedicated to the chamfered bevel. The grinding wheel achieves a material clearance of up to 3 mm at the back of the bevel, facilitating the assembly and holding of the lens in the bezel of strongly curved frames.
New reduced ecological footprint
Water consumption has been considerably reduced: the number of liters per lens ground is 5 liters (compared to 16 liters on average with old-generation grinders). ALTA PRO is therefore part of a new product development policy combining performance and respect for our environment.
Dimensions: L 510 x D 615 x H 570 mm
Weight: 79 kg
Voltage: 115 V – 50 Hz / 230 V – 60 Hz
THE STRONG POINTS ALTA PRO
▪ Significant optimization of your working time especially on highly technical assemblies.
▪ Exclusive range of features:
no need to subcontract difficult finishes.
▪ Unparalleled quality of finishes for a high-end result.
▪ Customizable grinder that adapts perfectly to your working habits.
▪ Water savings
▪ Briot Link remote maintenance.
| Column 1: Function or Feature | Column 2: Details |
|---|---|
| General Features | Automatic initialization |
| Feeling front & rear lens faces in 3 dimensions | |
| Equipment | Glass roughing wheel (Alta NX & NX SP only) |
| Roughing wheel for all plastics (CR39, high index, polycarbonate) | |
| Bevel/rimless finishing wheel | |
| Bevel/rimless polishing wheel | |
| Chamfering (facetting) wheel (Alta Pro only) | |
| Automatic Functions | Automatic clamping pressure |
| Automatic edging pressure adjusted according to substance to be edged | |
| Lens Grooving | Lens grooving in single or double width, i.e. L= 0,6 mm (Nylon thread) or L= 1,2 mm |
| Drilling | Drilling wide choice of holes (Alta Pro & NX only): open, closed, safetysinking, notches, oblongs |
| Drilling at variable angles (Alta Pro & NX only): parallel to the lens clamping shaft and lens holder shaft, perpendicular to the front face, perpendicular to the rear face | |
| Drilling-grooving function (Alta Pro & NX only) | |
| Safety Features | Safety-bevelling of front and/or rear faces of the lens |
| Connection for pump if operating in closed water circuit | |
| Dimensions and Specifications | Edging diameter |
| Bevel (without safety-bevel) | |
| Facette | |
| Grooving (without safety-bevel) | |
| Safety-bevel rimless/groove | |
| Safety-bevel | |
| Automatic cleaning of the lens fixing system and of the edging station | |
| Edging statistics | |
| Personalised machine configuration | |
| Network connection | |
| Option to extract emitted air and dust | |
| Designed for internal use | |
| Dimensions | |
| Weight | |
| Pump section outlet; power available (for the pump) | |
| Maximum water pressure | |
| Controls/mains insulation stepped up | |
| Noise level | |
| Degree of pollution | |
| Installation Category | |
| Ambient temperature | |
| Relative Humidity | |
| Maximum altitude | |
| IP 20 | |
| Compliance | Meets CEM – Di 2004/108/EEC (electronics) directives – RoHs Di 2002/95/EC |
| EN 55022 “Class B” | |
| EN 61000 -4 -2 // EN 61000 -4 -3 // EN 61000 -4 -4 | |
| Power Supply | Θ 230 V – 50 HZ EDGER |
| Input voltage | |
| Power consumption | |
| Electric power | |
| Fuses | |
| EC Standards | Meets Di 2006/95/CEE (electric) safety directives for 230 V – 50 Hz version |
| IEC 61010-1 | |
| Θ 230 V – 60 HZ EDGER | Input voltage |
| Power consumption | |
| Electric power | |
| Fuses | |
| ETL Marking | ⇒ UL 61010 – 1 |
| ⇒ CAN/CSA C22.2 N°61010 – 1 |
I wanted to know if all the calibration tools as well as accessories were available for each piece of equipment
This list is purely informative and in no way reflects reality. Please check the presence of the accessories in the photos below. No claim will be accepted. For more information you can consult the website
Do the photos correspond to the reference above or are they generic?
The photographs illustrating the products are contractual pictures. Photos are taken for each machine: each picture and each video are REAL ones.
Are your machines perfectly functional? And calibrated ready to cut?
The best machines and only “one first owner” models before, are choosen for being renovated process. Then, they are fully refurbished by our qualified technicians, and calibrated here in Montluçon, middle France. The products sold by SARL Digital Screen System are Second Hand market, so we encourage our customers to make an educated decision, take responsibility, and to remember that it’s still pre-owned ones, aesthetically and mechanically.
Get In Touch or Create an Account
Ready to Get Started?
You are hesitant, know that our products have been tested, for more information, contact us by email or whatsapp.